Products 1-48 of 70
Item #: CZG1496 -
Sheet metal mounting bracket for windshield washer bottle, as fitted in the engine compartment beginning approximately 1990, and in the boot on fuel-injected Minis.
Item #: 37H9712-ORIGINAL -
Washer bottle bracket in the original shape as used on Mk1 Minis. See 17H2536 for original shape water bottle; use with two (2) 37H9672 wire clips or one (1) 24A1387 spring clip, both sold separately.
4/5/2018 12:00:00 AM 19.9500
Item #: 37H9712 -
A modernized version of the metal bracket for the Mk1 windshield washer bottle, now in stainless steel.
Item #: WKB0101 -
Brush set assembly for 2-speed round wiper motor. Used approximately from 1969 until the end of production in 2000.
9/1/2017 12:00:00 AM 3.4900
Item #: 153511 -
This is the nut found on Mk3-on cars and is not the same thread as the 6-sided nut used on Mk1-2 cars.
Item #: 24A1387 -
Reproduction of the original bicycle-type spring clip for the water bottle on early Minis. Use on 37H9712-original bracket. See also 37H9672 wire clips used on earliest models.
6/20/2017 12:00:00 AM 8.50
Item #: 37H9672 -
Wire clips as used in a pair with very early Mk1 Mini washer bottle. Two (2) required.
Item #: 8B12396 -
Since Minis were built in both right-hand and left-hand drive versions, the windscreen cowl panel of later body shells was punched for either type of wiper configuration. Instead of filling
Item #: WGB225 -
Internal drive gear for round-bodied two-speed wiper motor. 110° arc.
Item #: WGB227 -
Wiper gear and shaft for 1-speed wiper motor, 120 degree sweep. Lucas number 54702585.
Item #: 740811 -
Threaded ferrule that fits into the end of the wiper motor, and hold the tube and wheel box assembly to the wiper motor; the correct part for the round-body 2-speed wiper.
Item #: 520161 -
Plug with short pigtail wires to fit round-body 2-speed wiper motor.
Item #: 150844 -
Small anti-vibration rubber pad for use with round body wiper motors as were used starting in 1968.
5/24/2017 12:00:00 AM 84.95
Item #: GWW935 -
Windshield washer fluid bottle. Fitted in the engine compartment from 1983 until October 1988, and in the boot from 1991-on. Rectangular.
Item #: GWW0952 -
Washer bottle cap for wide mouth version of early washer reservoir GWW0918. Use GWW0951 plug/tubing guide in the center of this cap.
Item #: GWW975 -
Blue cap with lanyard for windscreen washer bottle GWW935, which was fitted either under the hood or in the boot.
Item #: GWW0951 -
Cap and tubing outlet for GWW0906 washer reservoir. Also fits the center of GWW0952 cap.
Item #: GWW0906 -
One-liter water bottle as used from approximately 1970-1980.
Item #: GWW940 -
White plastic windshield washer reservoir, as fitted in the engine compartment on 1988-91 Minis.
Item #: 17H2536 -
For the restoration purist, we offer this reproduction of the Mk1 washer bottle. It features the original type narrow neck, and is the closest thing available to the original ADA3833 Winguard product.
Item #: GWW0829 -
After 1980, all Minis used this plastic washer nozzle, which pushed into a d-shaped hole in the cowl. Sold each. Use with GWW0202M 4mm bore tubing, sold per meter.
Item #: GWW807 -
Original shaped windshield washer jet for Mk1 and Mk2 Minis. Black plastic with metal nut.
Item #: GWW0802 -
Windscreen washer nozzle in chrome metal. Single jet is screwdriver adjustable for spray angle. Ideal replacement for obsolete plastic jets. Fits 3/16" hole in cowl. Use
Item #: GWW1192 -
Electric windshield washer pump, as fitted directly to the washer bottle In 1990 through 1996 Minis including SPi.
Item #: GWW0125 -
Small remotely mounted electric pump for windscreen washer jets. Mounts to firewall inside engine compartment.
Item #: GWW0130 -
Electric washer fluid pump, fitted to the reservoir bottle of some late Minis.
Item #: GWW0102 -
New Old Stock original push-button manual windscreen washer pump. Mounting bracket not included. Uses 1/4" tubing. These are increasingly hard to source, so please also see GWW0102E aftermarket pump.
Item #: GWW1116 -
If your washer bottle is in the boot, this is the pump fitted originally to MPis 1996-on.
1/8/2018 12:00:00 AM 4.95
Item #: GWW0401 -
T-fitting without check valve to distribute fluid to the washer jets on 1980-on cars. Use with GWW0202M tubing.
Item #: GWW0408 -
Washer fluid t-fitting with integral check valve. The inlet requires large tubing GWW0202M and the outlets to the jets require small tubing GWW0201M.
4/5/2018 12:00:00 AM 26.9500
Item #: GWW0918K -
This washer bottle is an ideal replacement for the cracked or missing washer reservoirs on early Minis. Note it is a modern version of the original Tudor bottle, with wider
Item #: GWW0202M -
Clear plastic windscreen tubing, 1/4" bore size. Sold per meter.
Item #: GWW0201M -
Clear plastic windscreen tubing, 1/8" bore size. Sold per meter.
Item #: GWW0515 -
Inline non-return valve for 1992-on cars with washer pump mounted in the boot.
Item #: GWW0504 -
Check valve for washer fluid in early Minis.
6/6/2017 12:00:00 AM 8.95
Item #: GWW0801 -
These chrome twin-jet windshield washer nozzles are a nice upgrade for most any Mini. Each jet is adjustable with a screwdriver for precise aim. Includes retaining nut and rubber
5/17/2017 12:00:00 AM 22.95
Item #: DKB101480 -
Left-hand parking black wiper arm for right-hand drive Mini. Has modern, hook-type end introduced in 1990; will fit Minis from 1970-on with correct blade.
5/17/2017 12:00:00 AM 22.95
Item #: DKB101490 -
Right-hand parking black wiper arm for left-hand drive Mini. Has modern, hook-type end introduced in 1990; will fit Minis from 1970-on with correct blade.
8/31/2017 12:00:00 AM 27.9500
Item #: 13H5630 -
Improve your Mini's wet weather vision with these heavy-duty wiper arms that hold the wipers down more securely in inclement conditions. These have a stainless heavy duty arm and spring
8/31/2017 12:00:00 AM 27.9500
Item #: 13H5627 -
Improve your Mini's wet weather vision with these heavy-duty wiper arms that hold the blades down more securely in inclement conditions. Parks on RIGHT side, as viewed from inside the
Item #: SEL0154 -
Reproduction wiper arm in the sixties design. Stainless-steel material. Parks to the left when stopped. Sold each.
Item #: SEL0149 -
Reproduction wiper arm in the sixties design. Stainless material. Parks to the right when stopped. See 13H5627 for heavy-duty version.
Item #: GWB0223 -
11" stainless steel wiper blade to fit 5.2mm arm as used on Minis up to 1990. Cantilever design helps the blade to conform to the shape of the windshield.
Item #: GWB0202 -
10" Stainless steel wiper blade assembly. Fits 5.2mm straight bayonet wiper arm to 1990. Sold each.
Item #: GWB219 -
10" Stainless steel wiper blade assembly. Fits 5.2mm straight bayonet wiper arm, as used up to 1990.
Item #: GWB911 -
11" Black wiper blade fits all Minis from 1973 thru 2000. Unipart 'Multi-fit' includes three adapters. Made in UK.
8/31/2017 12:00:00 AM 18.9500
Item #: GWB220 -
U.K.-made 11" stainless steel wiper blades to fit only 13H5627 or 13H5630 wiper arms. 2mm wider to stop flexing.
Item #: WKB105 -
Early Minis with a squared wiper motor body would use this brush set.