Lamp Covers, Brackets, Rims, & Gaskets

Metal bracket that clips to the headlight bucket assembly and serves as the anchor point for the chrome headlight bezel.

Foam gasket to fit tail lamp lenses with integral clear reverse lenses, except for Altissimo-made units. Fits both left and right sides, two (2) per car needed; sold each.

Foam rubber lens seating gasket as used on Mk2 tail lamp. Sold each.

The Mk1 tail lamps use this sponge rubber gasket between the lamp base and the body. Fits both right and left sides.

The Mini Van, Estate (Wagon) and traveller (Woody) tail lamps use this sponge rubber gasket between the lamp base and the body. Fits both right and left sides.

This sponge rubber gasket fits between the lens and the tail lamp assembly on the Mk1 Mini, both right and left sides.

Headlamp adjuster screw kit includes two (2) adjuster screws, two (2) plastic nuts, and tension spring.

Chrome headlamp ring, includes retaining screw; no drain holes. Good-quality aftermarket?.

Premium chrome over stainless steel. Has two drain holes in bottom; includes retaining screw. Made in the U.K. by Wipac; sold each.

If you are replacing your headlight bucket, you likely want the metal bowl that supports the headlamp bulb itself. Sold individually.

Original-style metal headlamp bucket; fits all except self-leveling type. Sold each. See S5400 for plastic rust-proof replacement bucket.

Plastic bucket includes chrome inner retaining ring, aim adjusting screws, inner rubber gasket and hardware. Fits 7" round lamps.

Pair of clear plastic covers to protect your headlights. Fit underneath and are retained by the original bezel with no additional fasteners.

Stainless steel trim pieces fit over headlamps, below the lamp retaining ring. A very charming and period accessory.

Chrome-plated inner rim that retains the headlamp bulb in the inner bucket.

On the original MPI Mini with 4 front spot lamps, two of these brackets are in the central position. Use also XBU100640/650 outer brackets for this conversion.

Left-hand spot lamp bracket for MPI Mini with 4 front lamps, or for a car being retrofitted with original Rover lamps and brackets. Use also 2x XBU10044 central brackets and

Right-hand spot lamp bracket for MPI Mini with 4 front lamps, or for a car being retrofitted with original Rover lamps and brackets. Use also 2x XBU10044 central brackets and

Rubber seating gasket for under the metal license plate lamp housing as used on Mk3 and later Minis.

Thick rubber seal between the lens and on the body on original Mini pickup taillight. New old stock.

Lucas lamp cover with stylized lion and "Q" in vertical band of white, made by Newton Commercial. Manufactured authentically to the original design.

Lucas lamp cover with stylized lion and "LUCAS" text, made by Newton Commercial. Manufactured authentically to the original design, even encorporating the small clear window to show if the lamp remains switched on.

This nylon insert snaps into the square holes around the headlight bucket on original fenders; the headlight bucket retaining screws then thread into the insert.

This chrome over brass trim ring will fit over the square side marker lens on the front fender. Fits straight over the original lens and retained by bending the tag.

Brass rivet for headlight bezel, to give an original look for a correct and proper early Mini restoration.

Set of six (6) special screws with anti-vibration fiber washers for Mk2 and Mk3 Mini tail lamp lenses, approx. 1968 to 1975.

Pretty, oval head screw with straight slot drive to fit headlight bezel.

Rubber gasket found underneath the headlamp. It is not included with most headlamp assemblies or components, so must be purchased on its own. Sold each.

Foam rubber seal that goes between the headlight bucket and the fender on MPi Minis equipped with motorized self-adjusting headlights. Sold each.

Stainless steel mounting bracket for Wipac driving lamps, part number S6007 and S6078. Sold each. Attaches under bumper in the original bumper mounting holes. Sold individually.

Gasket for lamp base to body on Mk2 Mini Saloon. Left-hand side. See 37H2690 for right-hand.

Rubber seal between lamp base and body on Mk2 Mini Saloon. Right-hand side. See 37H2689 for left-hand side.

Left-hand side rubber gasket, or seal, for lamp base-to-body on Mk4 and later Mini Saloon with reverse lights in the tail lights.

Right-hand side rubber gasket, or seal, for lamp base-to-body on Mk4 and later Mini Saloon with reverse lights in the tail lights.