Products 1-48 of 66
Item #: SBO0698 -
Battery brace that attaches to the subframe mounting panel under the rear seat of the classic Mini Estate.
Item #: 24A1463 -
Metal battery cable channel that is welded to the bottom of the floor. It protects the cable from accidental damage. Located on the underside of the floor at the edge of the tunnel.
Item #: SBO0745 -
When the remote shifter was developed for the early Mini Cooper and Cooper S, the BMC factory used this sheet-metal plate to cover the existing hole.
Item #: 14A9781 -
One of two side brackets used to support the boot board. There are often damaged from abuse or rear end accidents. See also CK948 complete bracket set.
Item #: 14A6609/10 -
Genuine Heritage bracket for boot floor to the inner wheel arch. Choose right- or left-hand side.
Item #: SBO0108/9 -
Aftermarket bracket to fit rear inner wheel arch to floor in Saloon boot. Choose right- or left-hand side.
Special Order - Call for Details
Item #: 41.41.00.05 -
Cargo bed floor for Pickup and Van models. This is the ribbed flat panel, it does not include any other structural members.
Item #: ALA5527 -
Clip under front floor to secure fuel and brake lines, used from 1959-1990. Weld in place beside floor pan footwell and tunnel; use two (2) per car.
Item #: ALA5536 -
This bendable metal tab is spot welded to the underside of the floor to locate the brake and fuel lines. Use three (3) per side, total of six (6) per car.
2/25/2020 12:00:00 AM
Item #: ADO360020/30 -
Complete rear seat side bin to fit 1990-on classic Minis. Heritage, choose right- or left-hand side
Item #: 14A6494/5 -
Outer skin of rear seat side bin to fit Mk1 and Mk2 Saloons. Ash-tray panel and inner stiffener not included
Item #: SBO0729/30 -
Complete rear seat side bin to fit Mk3-on models. Choose right- or left-hand side.
Special Order - Call for Details
Item #: 22.33.00.00 -
Complete floor assembly for Mk2 Mini Mini Estate Wagon. Will also work for Mk1 if converting to remote shift. Includes inner and outer sills, seat crossmember, rear subframe heelboard mounting panel.
Special Order - Call for Details
Item #: CZH2669 -
This floor has the 1996-on revised shape footwells, with a gusset section down the left side to carry the fuel-injection lines on late classic Minis
Item #: SBO0662/3 -
Inner jack support bracket at seat crossmember. Bracket is welded inside the sill to reinforce the jack mounting point. Choose right- or left-hand side.
Item #: 14A8374/5 -
Genuine Heritage jacking point with a reinforcement repair part to attach to the crossmember extension for all Minis.
Item #: SBO0092/3 -
Properly-shaped lower door frame repair panel for all external-hinge classic Minis, including Mk1, Mk2, Mini Pickups, Vans, and Estates. Must be professionally welded in. Choose right- or left-hand side.
8/16/2018 12:00:00 AM
Out of Stock
Item #: CZH3314 -
This steel panel supports the rear load floor on Austin, Morris, and Leyland Mini Estate and Van, and and also serves as the step for the rear "barn doors".
Item #: 14A9023 -
The commercial Minis, the Van and Pickup, used this extension to lengthen the floor of the standard sedan. It is an essential part for the correct restoration of all the
Item #: SBO0734/5 -
Front floor repair section for for fuel-injected Minis. In 1991 the floor stamping was changed, not only for strengthening, but also to make room for the fuel lines on fuel-injected models. Choose left or right side.
5/18/2017 12:00:00 AM
Item #: BHM0009E/10E -
These tailored aftermarket floor sections are actually a better option than Rover's own repair panels. The front floors sections are the most frequently rusted. These have a properly shaped
Item #: SBO0736/7 -
Rear floor repair section for for fuel-injected Mini. In 1991 the floor stamping was changed, not only for strengthening, but also to make room for the fuel lines on fuel-injected models.
Item #: 11.33.01.37/38 -
Aftermarket full-length half floor section for the Mk1, Mk2, and Mk3 Mini Saloon. Inner sill included and 4-vent outer sill is welded in place. Choose right- or left-hand side.
Item #: HMP441004/5 -
This panel is half of a complete Heritage floor which has been cut down the center to enable shipping. Note that the only Heritage panel now offered is made from the latest version of the tooling, which was for 1990s fuel injected Minis at the end of production. Choose right or left side.
Item #: SBO0116/7 -
Full-length half floor with inner and outer sills. Ideal panel for extensive rust repair of Mk1 (1962-on), Mk2 and early Mk3 Saloons with 4-vent outer sills. Choose right- or left-hand side.
Item #: SBO0118/9 -
Full-length half floor with inner and outer sills. Ideal panel for extensive rust repair of Mk3 and later (pre-fuel injection) Saloons with 6-vent outer sills. Aftermarket; ships via UPS. Choose right- or left-hand side.
Item #: FS006R/L -
Accurate reproduction half floor, full-length with inner sill only. Includes seat belt anchor, forward sling shoe bracket, and clips on underside for hydro/brake lines. Choose right- or left-hand side.
Item #: SBO0072/3 -
Aftermarket full-length half floor section for the Mk1/Mk2 Van, Estate, and Pickup models. Inner sill included and 4-vent outer sill is welded in place; also includes the tabs on the bottom for supporting the brake lines, but these must be welded in place. Choose right- or left-hand side.
Item #: SBO0126/7 -
Full-length half floor section for the classic Mini Mk3-on Van, Estate, and Pickup models. Inner sill included and 6-vent outer sill is welded in place
Item #: SBO0112/3 -
Heel board patch for classic Mini Van and Pickup. Aftermarket, choose right- or left-hand side.
Item #: SBO0086 -
The heel board is the vertical panel at the rear of the floor section, to which the front of the rear subframe is attached; frequently rusted out at the attachment points. Reproduction for the classic Mini Saloon.
4/9/2018 12:00:00 AM
Item #: HMP441008 -
Complete heel board panel, as used at the rear of the Saloon floor and to which the rear subframe is attached. Genuine British Motor Heritage.
Item #: HMP441006/7 -
The most troublesome area of rust in the heel board is at the subframe attachment points. These half heel boards are ideal for repair in this area. Heritage; choose right- or left-hand side.
Item #: SBO0110/1 -
This full-length panel extends from front of the door opening to the heel board, including the section underneath the rear seat pockets. Choose right- or left-hand side.
Item #: SBO0262/3 -
Aftermarket left-hand inner sill for long wheelbase Mini Van/Estate/Pickup models. Mk3-on. Includes mounting pads for carpet studs.
Item #: SBO0260/1 -
Aftermarket inner sill for long wheelbase Mini Van/Estate/Pickup models. Includes mounting pads for carpet studs.
Item #: ALA7322 -
This bolt-on access panel had to be made removable so that the fuel tank could be installed. It forms the rearmost portion of the floor under the left hand side panel.
Item #: ALA7076 -
A pair of half-floor panels suitable for the classic Mini Moke; complete front to rear, but do not include the center tunnel. New panels, galvanized to help prevent rust, and suitable for any year (classic) Moke.
Item #: ALA7014/5 -
Classic Mini Moke weld-in inner hull section (bottom) with seat belt installation panel. Designed to replace lower 4” of the side pod where it contacts the main floor. Choose right- or left-hand side.
Item #: ALA7318 -
The weld-on panels that form the bottom of the Moke’s side pontoon boxes, and complete the floor. Includes the two (2) battery stands and the battery support. Suitable for any year classic Mini Moke.
Item #: ALA7003 -
Lower portion of the Moke toe board, with reinforcement panels. A critical panel, because the front subframe bolts to it.
Item #: CZH3214 -
Main mounting bracket for the handbrake lever assembly, welded onto the back of the seat crossmember and to the rear floor section. For rod change cars with late-type single cable handbrake only.
Item #: 14A6669 -
Main mounting bracket for the handbrake lever assembly, welded onto the back of the seat crossmember and to the rear floor section. For pre-rod change cars with twin cable handbrake only.
Item #: SBO0404 -
Steel support structure for the steering rack. Spot welds to the underside of the toe board.
Item #: SBO0076/7 -
Outer rocker (sill) panel, with 6 vents as used after about 1970, in standard width. Fits long wheelbase classic Mini Van, Estate, and Pickup
8/27/2019 12:00:00 AM
Item #: 14A9534E/5E -
A budget replacement 6-vent sill for all Mk3-on classic Mini Saloons (sedans). Choose right- or left-hand side.
4/9/2018 12:00:00 AM
Item #: 14A9534/5 -
Genuine Rover Saloon outer sill (rocker) panel in original dimensions, as used on all classic Minis with six (6) vents after about 1970. Must be welded in place. Choose right- or left-hand side.
Item #: BHM0003E/4E -
Aftermarket classic Mini Saloon sill panel, extra-wide to replace or to be fitted over the original 6-vent sill panel. Choose right- or left-hand side.