Products 1-48 of 53
6/11/2019 12:00:00 AM
Item #: JZX1394SS -
Sharp looking allen head screw to fit SU carburetor dashpot and float lid. Non-tarnishing stainless steel will look good for years!
Item #: AUD1004 -
.090 "Fixed" needle, Special tuning "5" for performance applications.
Item #: AUD1005 -
.090 "Fixed" needle, Special Tuning "6" for performance applications.
Item #: AUD1478 -
Fixed .090 AN carb needle for SU HS2 and HS4
Item #: AUD1261 -
.090 ''Fixed'' SU carb needle, ''M'' type, for standard Cooper S with twin HS2
6/20/2017 12:00:00 AM
Out of Stock
Item #: CUD1001 -
.090 floating needle for HS2, HS4 or HIF4 S.U. carburetor; AAB.
Item #: CUD1015 -
AAR spring-loaded or swing needle for SU HS2, HS4, or HIF4 carb.
Item #: CUD1017 -
.090 Floating Needle for HS2, HS4 or HIF4 SU Carb. Spring-loaded equivalent of the M needle.
Item #: CRK0101 -
Master repair kit for twin HS2 carbs, as fitted to many classic Mini Cooper models; includes throttle shafts, bushings, butterflies, jets, float needle/seats, and gaskets/seals
Item #: CSK51 -
SU service kit for minor rebuild of single HS2 carburetor. Includes jet tube, float needle & seat valve, gaskets
Item #: CSK59 -
Genuine SU service kit for minor rebuild of twin SU HS2 carburetors. Includes 2 jets, 2 needle valves, and gaskets for a thorough rebuild
4/3/2019 12:00:00 AM
Item #: 12A0006 -
Spacer for 1.25" HS2 carb; 3/16” thick aluminum as originally supplied. Sold each.
Item #: 1G2623 -
Spacer for 1.25" HS2 carb. Approximately .210" thick. Use three (3) 1G2624 gaskets per carb for most installations.
9/18/2019 12:00:00 AM
Item #: STL0013 -
Using the CarbSync is the fastest and easiest way to synchronize airflow through twin carbs; a must-have for anyone maintaining twin carbs
Item #: SIE0083 -
Dual carbs, as supplied on the original Mini Cooper S. These are carbs only, no manifold or linkage included.
Item #: AUC8103 -
Dashpot damper with black plastic cap. Fits the top of SU HS2 and HS4 carburetors.
Item #: AUC4587 -
Dashpot spring with 2.5 ounce rate at 2.625" length. Commonly found on performance tuned engines. The lower rate allows it to move up more quickly than with the standard red
Item #: AUC1170 -
Green dashpot spring for any SU HS carburetor. 12oz spring.
Item #: AUC4387 -
Dashpot spring with 4.5 ounce rate at 2.635" length. Commonly found on stock spec units and mildly tuned engines. Small diameter, as found on HS and early HIF series carbs.
Item #: AUC1167 -
SU dashpot spring with 8oz ounce rate. 1” diameter, as used on HS and early HIF-series carbs.
Item #: AUD2178 -
Left-hand rubber float chamber adapter for SU HS2 and HS4 carbs; used in twin-carb applications to set the carburetor floats at the proper angle
Item #: AUD2179 -
Right-hand rubber float chamber adapter for SU HS2 and HS4 carbs; used in twin-carb applications to set the carburetor floats at the proper angle
Item #: GSU0550 -
Float lid gasket for all SU HS side-float carburetors; fits SU HS2, HS4, and HS6 carbs
Item #: WZX1102 -
High-flow needle and seat valves; diameter is .096'' compared to .070'' for standard applications. For HS series carbs including HS2 & HS4
10/1/2019 12:00:00 AM
Item #: WZX1304E -
Economical, aftermarket version of the adjustable float for HS2 and HS4 SU Carbretors. Made of a material that is impervious to modern alcohol fuels.
Item #: WZX1304 -
In recent years, the replacement floats for SU carbs were an all-plastic job with no method of adjusting the float valve operation. To make matters worse, many suppliers stocked only
Item #: 12H0862 -
The gasket on the air cleaner elbow side of the carb. Bolts between the carb and elbow or directly to pancake filters on the HS2 carb only.
Item #: 1G2624 -
Gasket for 1.25" SU carb flange or spacer.
Item #: SIE0045 -
Grose Jet folat valve for all side-float SU carbs.
12/4/2019 12:00:00 AM
Item #: AUD4288 -
Small metal guide that retains the spring-loaded or "swinging" needle on SU HS or HIF carburetors
Item #: SIE0041 -
Complete kit to replace cracked or missing heat shields on twin HS2 setup. Black powder-paint finished. Includes interconnecting bridge, two shields and springs. See SIE0041SS for stainless steel.
Item #: SIE0041SS -
A complete heat shield kit in highly-polished stainless for twin HS2s. Includes two shields, bridge, and springs.
Item #: AUC1152 -
Knurled hinge pin for float in HS series carb fuel chamber. These are often worn or damaged from removal, so get one each time you change the float.
12/13/2018 12:00:00 AM
Item #: AUD449 -
Restore lost performance with a new SU HS2 (1.25") single carb to replace original one used on 850 and 998 Minis. Equipped with floating needle.
Item #: NT606041 -
Half-height 3/8" SAE nut for use on rear brake hoses, bonnet pin, and twin HS2 intake manifolds.
Item #: WZX1341 -
Jet bearing kit for ''fixed needle''-type SU HS carburetors, including HS2 and HS4
Item #: WZX1442 -
Jet bearing kit for ''swinging needle''-type SU HS Carburetors, including HS2 and HS4
Item #: BFS701SUL -
Linkage set for converting a later Waxstat type jet HS4 to the earlier, simpler plastic fixed jet.
Item #: AUC2114 -
Carburetor Jet Locking Spring for HS2 & HS4
Item #: AUD9141 -
Jet tube assembly for HS series carbs with plastic jet. This fits the front carb (radiator end) on twin carb installations. Green band designation; bore size .090".
Item #: AUD9142 -
Jet tube assembly for HS series carbs with plastic jet. This fits the rear carb (flywheel end) on twin carb installations and single HS4 installations
Item #: AUD2194 -
Replacement for the troublesome seal seal in the bottom of the float bowl on HS (side float) carburetors.
Item #: SIE0052 -
Universal linkage kit for twin SU carburetors. Includes throttle cable guide AEG349, throttle and choke linkages, throttle cable trunnion; order throttle return springs separately, AEC2075, two or three required.
Item #: WZX872 -
Linkage kit for twin HS2 carbs on Mini, Sprite or Midget. Includes 12A0310 original center rod with balance bar.
Item #: AUC1400 -
Lost motion lever, for throttle shaft
Item #: VZX1100 -
Float chamber fuel metering valve for HS series side-float SU carberettors. Needle has Viton tip for long life and to prevent sticking. Impervious to modern fuels. Standard
Item #: AUC2002 -
Jet locking nut for SU HS-type carburetor, as included in jet bearing kits WZX1442 and WZX1341. Sold each.
Item #: FOR146 -
Pair of rubber isolating spacers for vintage race Minis using period correct SU H4 carburetors. By eleminating vibration, helps to eliminate high rpm vibration-related misfires.