Products 1-48 of 299
Item #: SBR0007 -
Disc brake conversion for use with 12” or 13” wheels; includes everything necessary to convert your classic Mini from drum brakes 8.4” front disc brakes. Reproduction calipers and wheel bearings.
Item #: SAC0011 -
These aluminum alloy pedals will help you with spirited driving and look great, too. Grippy pattern keeps your feet in place.
11/16/2017 12:00:00 AM 89.9500
Item #: 21A1058 -
A couple of part numbers have been used for the rear backing plates. The only difference is the holes in the backplate that accept the wheel cylinder. Depending on
9/11/2017 12:00:00 AM 89.9500
Item #: 37H2014 -
OEM brake backing plate assembly for twin leading shoe front brakes. Left side. Repair kits for the brake adjusters are no longer available. If the shoes cannot be properly adjusted
9/11/2017 12:00:00 AM 89.9500
Item #: 37H2013 -
OEM brake backing plate for the RH side of all twin leading shoe front brakes. Repair kits for the brake adjusters are no longer available. If the shoes cannot be
Item #: 17H2477 -
Single leading shoe front brakes are identified by a single wheel cylinder per backing plate. This plate replaces the earlier design. New Old Stock.
Item #: 7H7995 -
Located on right side of front subframe near flywheel bell housing.
Item #: C5192 -
All Verto clutch slaves use this hollow bolt to attach the flex hose to the cylinder. Also used on some brakes switches used with tandem master cylinders. Was
Item #: CRC8664 -
Master cylinder base plate for cars with servo built into the brake master cylinder; for Minis from 1989-on.
Item #: HDWS279 -
This is the larger of the two brake bleed screw sizes used commonly on the classic Mini; usually found on disc brake calipers, twin-leading front cylinders, clutch slaves and various piping applications
6/20/2017 12:00:00 AM 2.9500
Item #: HDWS289 -
This is the smaller of the two brake bleed screw sizes used commonly on the classic Mini; used primarily on rear wheel cylinders.
Item #: HDWS290 -
M7 bleed screw to fit cast iron Turbo; Metro brake caliper.
Item #: BTA0370 -
Special bolt to fasten 8.4" brake rotor (12" wheel cars)to 21A2695 drive flange. Use eight (8) for this application.
Item #: HDWB2742/M -
Small 1/4" x 3/8" hardware bolt as used on wheel cylinders, timing covers, and 1974-on one-piece radiator housing. Sold each.
11/10/2017 12:00:00 AM 5.9500
Item #: 17H7612 -
Rubber boot to seal handbrake lever entry into backing plate. Fits both sides.
Item #: 21A1522 -
For Hydrolastic cars only, this bracket clamps under the clutch pipe and top engine steady bulkhead bracket to retain the brake line and hydrolastic pipe.
Item #: 21A1522-USED -
Refurbished bracket, for Hydrolastic cars only; clamps under the clutch pipe and top engine steady bulkhead bracket to retain the brake line and hydrolastic pipe.
Item #: SBR0009 -
For performance applications, upgraded brake hoses are a must! Teflon-lined inner hose is protected by stainless steel braided covering; for use with front disc brakes.
Item #: SBR0011 -
Stainless hose set as SBR0009 but including a clutch hose for pre-Verto setups. See C-AJJ4027B for Verto 5-piece kit.
Item #: C-AJJ4027B -
Racing Teflon-lined stainless braided hose set with banjo clutch hose as required for Verto clutch cars.
Item #: C-AJJ4030 -
Front hose kit only. Correct length for use with disc brakes; hardware included. Sold per pair.
8/10/2017 12:00:00 AM 104.9500
Item #: C-AJJ4024 -
Special conversion brake hose set in braided stainless material for installation of 4 piston Metro calipers on a Mini.
8/10/2017 12:00:00 AM 49.9500
Item #: C-AJJ4031 -
Pair of rear hoses only in racing spec Teflon-lined braided stainless material.
Item #: C-AJJ4031B -
Designed for radically lowered Minis to avoid the rear metal brake pipes being crushed, these special hoses have a banjo bolt and fitting for the cylinder end of the hoses.
Item #: 17H7620 -
The brake adjusters on your rear brakes will wear and become less adjustable over time. The result will be excessive pedal travel. This adjuster kit for drum brakes includes
Item #: STL0011 -
Has a 1/4" hex on one end for rear bleed valves, and a sturdy 5/16" open end on the other end for adjusting screws.
Item #: SBR0075 -
A complete set of bolt-on front brake backing plates with shoes, wheel cylinders, springs, etc., all brand new. Ready to install on your car after fitting SPA10 metal brake pipes (sold separately).
Item #: M10 -
Replacement 10mm metric bleed screws to fit 4-pot aluminum calipers. Generally two (2) used per caliper.
Item #: GBC0138 -
Left-hand side brake caliper. Once 12" wheels were fitted to disc brake Minis starting in 1984, a bigger caliper was added to give better braking.
Item #: GBC0141 -
Right-hand side brake caliper. Once 12" wheels were fitted to disc brake Minis starting in 1984, a bigger caliper was added to give better braking.
10/23/2017 12:00:00 AM 169.9500
Item #: 27H4656E/7E -
A lower cost alternative to the original brake caliper for 7.5" Cooper S brakes.
Item #: 27H4657 -
Genuine AP Caparo. Stock Cooper S caliper offers great stopping under a 10" wheel. Mount with bleeder in upright position, and check for adequate clearance with your wheels. (Right hand
Item #: 27H4656 -
If you are upgrading to Cooper S spec, you'll need a pair of these. Always install with bleed screw pointed up and check for wheel clearance, since some 10" steel
Item #: GDB0105 -
This drum has no built in wheel spacer. It fits the front of all drum-braked Minis and the rears of all that don't require a built-in wheel spacer. Sold each.
11/16/2017 12:00:00 AM 34.9500
Item #: GDB0106 -
Original Mk1 Cooper and S rear drums had an integral spacer cast into the drum. This same drum is used at the rear on on all later disc brake cars,
Item #: SBR0002 -
Lightweight finned aluminum brake drum using a cast-in steel friction surface and integral spacer. Direct replacement for Cooper S brake drum. Fins aid in strength and cooling. Sold as a
Item #: MSSK1401 -
Disc brake dust shield kit, Cooper S, left-hand side. Small strap BTA1209 not included.
Item #: MSSK1400 -
Disc brake dust shield kit, Cooper S, right-hand side. Small strap BTA1208 is not included.
Item #: SBR0029 -
Unique formula engineered to provide outstanding performance in todays high temperature braking systems. Provides optimum braking response. Exceeds DOT3 and DOT4 specifications.
Item #: SBR0028 -
LMA stands for Low Moisture Affinity, which helps overcome one of the drawbacks of convention brake fluid. Standard fluid absorbs a lot of moisture from the atmosphere, which deteriorates its
Item #: SBR0037 -
CASTROL SRF Racing Brake Fluid is an ultra high performance product formulated specifically to satisfy the ever increasing stresses placed upon the braking systems used road racing.
Item #: SBR0141 -
DOT4 Brake fluid specifically formulated for use with the natural rubber seals in your brake hydraulics. 500ml bottle.
Item #: HDWN306 -
Large nut used on the subframe end of front brake hoses.
Item #: GBH0117 -
Brake hose to rear subframe, for MG1100/Austin America.
Item #: GBH0249E -
The disc brake hose is shorter than the drum brake hose and has a reinforcing sleeve on the inner end. Reliable aftermarket supplier. Sold each.
Item #: GBH0170E -
Drum brake front hoses are slightly longer than disc brake hoses. Quality aftermarket manufacturer. Sold each.
Item #: GBH0250E -
All Minis use the same rear brake hoses. Reliable aftermarket manufacturer. Sold each.
Item #: 13H3735 -
Starting in 1981, the brake pressure switch was moved to the pedal box location.