Products 49-96 of 544
Item #: CZG1496 -
Sheet metal mounting bracket for windshield washer bottle, as fitted in the engine compartment beginning approximately 1990, and in the boot on fuel-injected Minis.
Item #: 37H9712-ORIGINAL -
Washer bottle bracket in the original shape as used on Mk1 Minis. See 17H2536 for original shape water bottle; use with two (2) 37H9672 wire clips or one (1) 24A1387 spring clip, both sold separately.
4/5/2018 12:00:00 AM
Item #: 37H9712 -
A modernized version of the metal bracket for the Mk1 windshield washer bottle, now in stainless steel.
Item #: 13H3735HD -
Beginning in 1976, the brake pressure switch was fitted to the pedal box location. This premium example should have a longer life expectancy than the standard.
Item #: C16062 -
If your Mini has no brake lights the switch is the most likely culprit. The pressure of the brake fluid activates this switch which screws into a fitting on the
Item #: C16062HD -
The pressure of the brake fluid activates this switch, which screws into the banjo fitting on the front subframe on the right side.
Item #: WKB0101 -
Brush set assembly for 2-speed round wiper motor. Used approximately from 1969 until the end of production in 2000.
Item #: TAB128 -
Set of four (4) brushes found in the early 35G-1 inertia starter.
Item #: TAB117 -
Later inertia starters, model 35J, used these brushes. Sold in a set.
Item #: 576986 -
Single function socket for early turn signal lamp, as used on UK cars with parking lamp bulb inside main headlamp. Use with 382 bulb.
Item #: 576985 -
Dual function (turn indicator and parking light) for early "beehive" front indicator lamp, as fitted to non-UK Mini models. Use with 380 bulb. See 576986 for single function socket.
12/6/2017 12:00:00 AM
Item #: AEU1313A -
Light socket with ground wire for center-binnacle speedometer.
Item #: 239 -
Bulb, Courtesy Lamp. Tubular or "Festoon" style.
Item #: 380 -
Bulb, dual element, as used on U.S.-spec front turn signal and all rear brake/tail light.
Item #: GLB453 -
55-watt H3 bulb to fit driving and fog lights. Sold each.
Item #: 989 -
Small based bulb, most commonly used in Mk1 & Mk2 license plate lights. Also used in side marker lights on Canadian Minis, and other applications.
Item #: 281 -
Bulb, panel, bayonet type. Push in and twist 1/4 turn. Typically used on oil and water temp gauges.
Item #: 987 -
Panel bulb. Screw-in style.
Item #: GLB501A -
Amber bulb for 1986-on wing side marker lamp. 5-watt, push-in bulb. Also available in clear as GLB501.
Item #: GLB501 -
Clear bulb for 1986-on wing side marker lamp and also modern headlamp units with Euro-spec pilot light. 5-watt, push-in bulb. Also available in amber as GLB501A.
Item #: 382 -
Front turn lamp and rear flasher, all years 1959-2000.
Item #: GLB207 -
Single element 5W bayonet-mount bulb.
Item #: GLB343 -
Single-elment turn-signal bulb in amber; for use with clear or white-colored beehive lenses. Not for use with twin-point Minis (after 1996).
Item #: GLB280 -
Quite possibly the smallest light bulb you'll ever see! Unique style on the early Mini and Morris Minor feature is the stalk-mounted turn signal indicator; 47H5200 is the lens, GLB280
Item #: CWB330 -
Bullet Solderless Wire Tip to Lamp
Item #: TCB124 -
Minis used the M35G-1 starter model originally, identifiable by the removable brush covering band. If the front bush is worn, this is the correct one for this model.
Item #: TCB125 -
The 35G-1 starter was the earlier of the two inertia types. The rear bushing must be replaced if it shows excessive wear.
Item #: CZB103 -
Zinc-plated flag type cable clip. 3/8" diameter, suitable for securing battery cable.
Item #: 5L925 -
A 24" cable with correct end fittings to connect from the engine-bay starter solenoid to the starter on cars with inertia starter.
Item #: NSC100760 -
Plastic-bodied cam timing sensor for engine management of MPI Minis. Fits in mechanical fuel pump hole in the block. Genuine Lucas product.
9/1/2017 12:00:00 AM
Item #: 153511 -
This is the nut found on Mk3-on cars and is not the same thread as the 6-sided nut used on Mk1-2 cars.
Item #: BEZEL01 -
Chrome retaining ring for horn-push logo on Mk1 Austin and Morris Minis.
Item #: 14A9907 -
Oval chrome metal trim strip that surrounds the 3 center-mounted gauges on Deluxe/Cooper models. Uses 14x 14A9796 wire retaining clips. Also make a small metal tab to connect the
Item #: AAU1818 -
Small clamp to fit FAM2807 rubber oil pressure gauge hose.
Item #: MSSK035 -
Upper tail light lenses in clear with amber and red bulbs for converting the rear of a Mk4-on Mini to a customized clear lens look. Includes parts for both sides.
Item #: GHF0771 -
Small spring clip to receive the mounting screw of "beehive" front indicator lamps. Use three (3) per lamp.
Item #: 37H7421 -
Metal bracket that clips to the headlight bucket assembly and serves as the anchor point for the chrome headlight bezel.
Item #: 14A9796 -
Small wire bow-tie clip to retain the oval chrome trim on the plastic gauge pod for Deluxe and Cooper models with center guage location. Normally, fourteen (14) are required. Sold
Item #: AFU2770 -
This clip is used to secure the speedometer cable against the firewall, to keep it from touching the exhaust, on all center binnacle Minis 1959-1984.
Item #: 24A1387 -
Reproduction of the original bicycle-type spring clip for the water bottle on early Minis. Use on 37H9712-original bracket. See also 37H9672 wire clips used on earliest models.
6/20/2017 12:00:00 AM
Item #: 37H9672 -
Wire clips as used in a pair with very early Mk1 Mini washer bottle. Two (2) required.
Item #: SIB110 -
Smiths clock in 52mm size. Black face with chrome bezel.
Item #: SIB110MG -
Genuine Smiths clock in magnolia face. 52mm size.
Item #: 12G2994-USED -
Restored A+ coil bracket that mounts on cylinder head stud.
6/11/2018 12:00:00 AM
Item #: GCL0204 -
Ignition coil pack for MPi Mini.
Item #: DLB198 -
High-output Sports Coil for 1984-1996 classic Minis.
Item #: 40001 -
Chrome PerTronix Flame-Thrower ignition coil for Minis with a ballast resistor in the ignition wiring, typically 1984 to 1996.
Item #: 40611 -
This black 40,000 volt Flame-Thrower ignition coil is a perfect complement to the Pertronix inductive Hall Effect distributor module.