Products 49-96 of 767
Item #: ALA6515 -
Morris Cooper oval bonnet badge, Mk2-on. Use with bezel ALA6519.
Item #: 24A1401 -
Small 'S' badge as used over bonnet badges on Mk1 Austin and Morris Cooper S models, and over Mk1 Morris Cooper boot badge. Approx. 7/8" x 5/8".
10/11/2018 12:00:00 AM
Item #: AXE4243 -
Speedwell was owned by the late Graham Hill, who died in the mid-70s. This was the special bonnet badge denoting the company and fitted to their cars, sometimes front and rear.
Item #: SBO0265 -
Bonnet cloth braid to prevent metal-to-metal contact. Sold in one-meter lengths.
Item #: ADU2072 -
In about 1990, the rubber bumper on the "slam panel" was deleted and a small stick-on bumper was added at the sides to locate the bonnet. Of course, these
Item #: BMP0348/9 -
Bonnet hinge for 1980-on classic Minis; choose right- or left-hand.
Item #: 14A7246/7 -
Bonnet hinge for Mini Mk1 and Mk2, manufactured new by British Motor Heritage from original tooling. Choose right- or left-hand; sold each.
Item #: SAC0025 -
This pair of rubber hooks can be used as quick release fasteners on almost anything. On the Mini they are most often used to secure tilt front-ends or removable bonnets.
Item #: HYK2570 -
Rubber bonnet hook to secure the Moke hood. Fits snugly over the existing peg on the body and into the receiver on the hood. Sold each.
Item #: SAC0035 -
These lightweight rubber hooks are most commonly used to secure fiberglass boot lid or bonnet on the Original Mini.
9/13/2018 12:00:00 AM
Item #: 14A6493K -
Bonnet release assembly for Mk1 Mini, 1959-67, plus classic Mini Vans and Pickups. Bolt to the slam panel.
9/13/2018 12:00:00 AM
Item #: ALA6992K -
The Mk2 bonnet release latch was reached through an opening in the grille; the curved hook made the release easier to reach than on earlier models.
Item #: AAM1206-USED -
Includes latch, guide plate, and hardware. As used on the Mk3 Mini up until the introduction of the internal bonnet release. Used.
5/16/2018 12:00:00 AM
Item #: 14A6586 -
Latch pin that attaches to the bonnet and helps hold the hood to the front panel when closed. A worn pin can lead to the hood self-releasing at an inappropriate
Item #: FPS10002 -
Bonnet latch (catch) for use with internal cable release, as fitted 1993-1996.
Item #: FPS100340 -
Bonnet latch (catch) for 1997-on Mini, identified by plastic guide sleeve in center.
9/5/2017 12:00:00 AM
Item #: SBO0363 -
Starting with the Mk2 in 1968, all Minis have used a chrome grille trim piece attached to the front edge of the bonnet. The trim mounts to this extension, which
Item #: SAC0130 -
Quick-release, heavy duty bonnet pin set; includes pins, clips, finishing plates, and cable tethers so you don't lose the clips.
Item #: 14A7806 -
Small sheet metal bracket on right inner fender inside engine bay to accept the lower end of the bonnet stay rod.
Item #: CZH0209 -
Beginning with Mk3 models, the bonnet prop clip was made from metal instead of rubber.
Item #: BKD360030 -
Stock steel bonnet prop rod replaces 24A0857. It has changed a little over the years so may not match your old one exactly. Genuine Rover.
Item #: SBO0022 -
The straight bonnet prop rod as used on Mk1, Mk2, and Mk3 Minis; reproduction part made of polished stainless steel.
6/5/2018 12:00:00 AM
Item #: 2H9215 -
Rubber clip on Mk1 and Mk2 bonnets to accept the prop rod.
Item #: FOR028 -
Quick release bonnet hinges replace the original bonnet hinges on the Mk3-on Mini, making it easier to work on your engine without bumping your head. The old hinges are often
Item #: FOR027 -
Quick release bonnet hinges replace the original bonnet hinges on Mk1-Mk2 Mini models, making it easier to work on your engine without bumping your head. The old hinges are often
Item #: JRC8000 -
Push-on rubber and metal seal for MPI Minis. This was unique in that it was longer than just the rear channel, and includes enough material to extend forward by about
6/7/2017 12:00:00 AM
Item #: FSE10020 -
Bonnet release cable for right-hand drive cars to VIN BD134454. See FSE100420 for later cars.
Item #: ALA7608 -
Safety hook to provide a secondary means of keeping the bonnet shut.
Item #: ALA7608OEM -
Bonnet safety catch, with spring, pin, and mounting bracket. Provides a secondary means of keeping the bonnet shut should the bonnet latch comes loose.
Item #: JRC7898 -
This v-section seal fits across the front of the bonnet on late Minis, usually from Mk3-on. It helps prevent the bonnet from vibrating against the front panel crossmember and reduces
Item #: JRC7008 -
This seal is found at the rear of the engine bay and helps prevent the ingress of water and debris into the engine compartment. Usually found on Mk3 and later
Item #: 14A9010 -
Self-adhesive neoprene seal that fits in the channel of the windshield cowl. Creates a seal when the bonnet is closed.
Item #: SBO0742 -
Aftermarket replacement outer skin only for bonnet; un-primed steel. Fits round-nose classic Mini from 1959-2000.
Item #: SBO0046 -
The “slam panel” is that part of the front panel on to which the bonnet closes. Fits classic Minis from 1959-1996, excluding Clubman
Item #: SBO0049 -
Bonnet slam panel for 1997-on Minis. Not for Clubman fronts.
Item #: AAU5486 -
Small rubber bumpers to prevent the bonnet from slamming down or rattling on Clubman Minis. Sold each.
Item #: SAC0079 -
Special Tuning Works style single bonnet strap in original tan. Single bonnet strap, as used by the Special Tuning Department on works Minis. This very heavy duty bonnet strap is
Item #: SAC0080 -
Single bonnet strap, as used by the Special Tuning Department on works Minis, but in black. This very heavy duty bonnet strap is a excellent reproduction of the original. 3.3mm
Item #: MSA112_Color -
Pair of John Cooper-style bonnet stripe decals. Choose from white (MSA1120), black (MSA1121), or silver (MSA1123).
Item #: MSSK018 -
Bolts to an existing hinge and is spring loaded to act as an auxiliary bonnet prop. Once installed it will assist the opening of the hood and reduce the tendency
4/9/2018 12:00:00 AM
Item #: BKA360070 -
Bonnet for UK-spec MPi Minis with front-mounted radiator. Genuine Rover. The hood latch and safety catch are unique on these late model cars and this is the proper bonnet to
Item #: KAD1013250 -
Fiberglass bonnet made by KAD specifically to clear their twin-cam cylinder head. Special order, allow 3-6 weeks.
Item #: CZH0296E -
A reproduction version of the Mk1 bonnet, which has no extension for the grille trim used on later Minis.
Item #: SBO0007 -
Fiberglass bonnet skin for Mk1-style race Minis (without front trim lip). No internal structure or provision for mounting; ready to sand and paint.
4/9/2018 12:00:00 AM
Item #: 24A1182 -
Bonnets from Mk1 cars are identified by having no lip on the front to mount the upper grille trim used starting on Mk2 models. Plus the hinge brackets are spaced
4/9/2018 12:00:00 AM
Item #: ALA7455 -
Genuine Heritage bonnet for 1968-69 cars only. Has narrow hinge spacing as used on Mk1-2 cars but with Mk2-on grille trim lip on the front.
Item #: SBO0070 -
Fiberglass bonnet skin only for race use. Ready to sand and paint. For Mk2-on Minis with front lip for upper grille chrome. No internal structure or provisions for mounting or
Item #: SBO0362 -
A good-quality reproduction panel from a reliable U.K. manufacturer; with front lip for mounting upper grille trim. Hinge brackets are spaced for Mk3 through SPi cars (1995).