All Products

Latch pin that attaches to the Classic Mini bonnet (hood) and helps hold it to the front panel when closed. Ref: 14A6586.

Latch pin that attaches to the classic Mini Clubman bonnet (hood) and helps hold it to the front panel when closed. Ref: 14G2444.

Classic Mini bonnet latch (catch) for use with internal cable release, as fitted 1993-1996. Ref: FPS10002.

Mk2-on classic Mini bonnet lip extention body panel.

Quick-release, heavy duty bonnet pin set; includes pins, clips, finishing plates, and cable tethers so you don't lose the clips.

Small sheet metal bracket on right inner fender inside engine bay to accept the lower end of the bonnet stay rod

Metal bonnet (hood) prop clip as used on Mk3 and later classic Minis; holds the prop when the bonnet is closed. Ref: CZH209.

Stock steel bonnet prop rod; this style has changed a little over the years so may not match your old one exactly. Ref: BKD360030, 24A857.

Polished, straight stainless steel bonnet prop rod as used on Mk1, Mk2, and Mk3 classic Minis.

Rubber clip on Mk1 and Mk2 classic Mini bonnets (hoods) to hold the prop rod. Ref: 2H9215.

Quick-release stainless bonnet hinges to replace the original bonnet hinges on the Mk3-on classic Mini.

Quick-release stainless bonnet (hood) hinges to replace the original bonnet hinges on Mk1-Mk2 classic Mini models.

Push-on rubber and metal seal for MPi (multi-point injection) classic Minis.

Bonnet release cable, as standard on all classic Minis from 1992/3 to 2000. Ref: FSE10020.

Safety hook to provide a secondary means of keeping the bonnet shut. Ref: ALA7608, 14A366.

Bonnet safety catch, with spring, pin, and mounting bracket. Provides a secondary means of keeping the bonnet shut should the bonnet latch comes loose.

V-section seal fits across the front of the bonnet on late classic Minis; helps prevent the bonnet from vibrating against the front panel crossmember. Ref: JRC7898, CZH1953.

Seal found at the rear of the engine bay; helps prevent the ingress of water and debris into the engine compartment. Ref: JRC7008.

Self-adhesive neoprene seal that fits in the channel of the windshield cowl. Creates a seal when the bonnet is closed.

Lightweight fiberglass bonnet skin (only), ready to sand and paint. For classic Minis Mk2-on with front lip for upper grille chrome. Ref: SBO0070, MS114A, MAG002, CFG-3.

The ''slam panel'' is that part of the front panel on to which the bonnet closes. Fits classic Minis from 1959-1996, excluding Clubman.

''Slam panel'' for MPi classic Minis with front-mount radiator; part of the front panel on to which the bonnet (hood) closes. Ref: 14A6562, SBO0049.

This four-piece soundproofing kit is cut out exactly to fit between the classic Mini bonnet (hood) cross-bracing frame. Ref: 47H9615, G0822.

Small rubber bumpers to prevent the bonnet (hood) from slamming down or rattling on classic Clubman Minis. Sold each.

Original-style heavy-duty leather straps for securing the bonnet/hood of the classic Mini, in tan or black. Ref: C-AJJ3380, C-AJJ3381.

Pair of Cooper-style bonnet stripe decals, sized for the Mk2 and later classic Minis. Ref: MSA1120, MSA1121, MSA1123.

Bolts to an existing hinge and is spring-loaded to act as an auxiliary bonnet prop. Ref: MSSK018.

As-original British Motor Heritage-produced classic Mini Clubman bonnet/hood. Ref: CZH2609

Bonnet (hood) for 1997-on U.K.-spec MPi classic Minis with front-mounted radiator. Ref: BKA360070, BKA360070/HTG.

A reproduction version of the Mk1 bonnet, which has no extension for the grille trim used on later Minis.

Bonnets from Mk1 classic Minis are identified by having no lip on the front to mount the upper grille trim used starting on Mk2 models. Ref: 24A1182, 24A1182/HTG, 24A1182ORIG.

Genuine Heritage bonnet/hood for 1968-69 classic Mini only; can be used on Mk1 Minis if updating to the Mk2 grille. Ref: ALA7455, ALA7455/HTG.

Good-quality reproduction classic Mini bonnet/hood panel for Mk3-on models, from a reliable U.K. manufacturer. Ref: MSL2, CZH455, SBO362, SBO0362.

Precise-fitting Rover-style bonnet made from the original tooling; hinge brackets to fit Mk3-on spacing. Ref: CZH455, BKA360100, CZH0455.

This quality Heritage-made bonnet is designed for classic Mini Vans and Pickups starting in about 1971.

''Mini'' script boot badge as used on Mk1 MK2 classic Minis. Ref: 24A997, 24A0997.

Chrome, block letter ''1000'' badge, as used on the Austin and Morris Mk2 Cooper. Ref: ALA6695.

''1275'' block letter badge for the Mk2 classic Mini boot (trunk) lid.

Chrome boot (trunk) badge as fitted to Cooper Sport model. Ref: DAH100920MMM.

These ''GB'' badge letters are made in stainless steel to the correct bend and shape to fit the boot lid on classic Minis.

Boot lid badge for the classic Mini 1000, with the Leyland logo. Ref: CZH3815, CZH1357, CZH4152.

Chrome, black and gold metal boot badge, originally fitted the 1984 Special Edition classic Mini. Ref: CZH4016.

Chrome ''Austin'' script boot badge as fitted to Mk1 Austin Mini, Austin Cooper and Austin Cooper S models. Ref: 14A6802.

Self-adhesive boot badge as used on classic Minis from 1992-on. Chrome finish with contrasting black edges.

Black and silver boot (trunk) badge as fitted to Clubman-bodied 1275GT classic Mini. Ref: CZH1269.

Boot badge, outline script of the word ''Cooper'' in chrome-plated metal. Ref: 24A23, BAD24A23, 24A0023.

This is the script ''S'' for classic Mini Cooper S models; not symmetrically mounted once installed. Ref: 24A1402.

Classic ''Mini-Minor'' Mk1 boot (trunk) badge, in chrome block letters. Ref: ADA3730.